Harman Stove Company PB 105 Manuale Utente

  

10Fig. 3Avoiding Smoke and Odors - Negative Pressure, Shut-down and Electrical Power Failure.To reduce the probability of back-drafting or burn

11The minimum vent conguration is a 90o or Tee on a starter collar and a 24” length horizontal through an exterior wall. A cap on the end should di

12Chimneys taller than 20’ above the connection will require a draft test to determine if the draft is too high.Note: The high burn draft shoul

13Outside AirTo install outside air, use 2 3/4” I.D.galvanized steel ex pipe, part # 2-00-08544 ( 12’ 6” length) or part # 2-00-08545 ( 25’ lengt

14To install power to the boiler, rst remove the cover on the 4” X 4” junction box located on the back of the unit. There are

15Installing DuctCold return water temperature (Sustained temperatures below 140 degrees Fahrenheit) will lead to condensation in th

16Installing Duct/Air ConditioningBoilers intended to be connected to an existing boiler or boiler system shall:1. Be capable of being ins

17NOTE: ALWAYS REFER TO THE INDIVIDUAL COMPONENTS RECOMMENDED INSTALLATION INSTRUCTIONS FOR THE PROPER MOUNTING POSITION AND LOCATION WITHIN THE PIPIN

18* PRESSURE RELIEF VALVE* TEMPERATURE/PRESSURE GAUGEAIR VENTTYPICAL BOILER HOT WATER PIPING SHOWING AIR REMOVAL SYSTEM, PROVISIONS FOR TH

19Cold return water temperature (Sustained temperatures below 140 degrees Fahrenheit) will lead to condensation in the rebox. This

20 20OverHeat Safety Zone (Dump Zone): STRONGLY RECOMMENDED in all installations.When the pellet boiler is operating at High burn

21 Draft Test ProcedureAfter the venting is completed, the rebox low draft will need to be checked and possibly adjusted. After removi

22Fuel and Fuel StoragePellet fuel quality can uctuate from manufacturer to manufacturer, and even from bag to bag. Hearth & Home Technologies re

23Power LightIndicates power to the control board.Status LightWill be lit anytime there is a call for heat.Combustion Blower LightIndicates Power t

24Setting The Boiler TemperatureWithout the Outdoor Air Temperature Sensor Installed To set the maximum boiler water temperature, sim-ply turn

25Pellet Boiler Outdoor Air Reset OperationWhen the outdoor sensor is installed, at 20° F. or below OAT (Outdoor Air Temperature), the boiler

261. Turn Mode Selector to “OFF”.This resets the control in addition to turning it off. Starting A Fire Automatically2. Clean Burnpot with sc

274. If Starting After an Empty Hopper, Turn Feed Adjuster to “TEST” (for one 60 second cycle). This will feed pellets into the auger tube and

288. Turn the MIN. TEMP. Dial on the control board to the desired Minimum temperature. This will start the lighting process if the temperature at the

29NOTE: Stirring the starting gel into the pellets usually allows the re to become established quicker.CAUTION: A vapor ash could occur if

3Hopper Lid LatchesHopper Control Board CoverControl BoardCombustion BlowerCombustion Blower CoverTemperature / Pressure GaugePressure Relief ValveAqu

30Fig. 18Burnpot Cleaning: The burnpot should be cleaned no less than once a week. For best operation the burnpot should be cleaned every time the hop

31Ash RemovalIt is recommended to remove the ashes when the boiler is not in operation. This lessens the chances of coming in contact with

32CleaningThis cleaning should be done after each ton of pellets used. The frequency of this cleaning will be directly related to

33The boiler MUST be OFF and COOL before you should attempt to clean the combustion blower.The wire to the combustion blower doesn’t need t

34 1. No pellets in hopper.2. Firebox draft may be too low for low draft pres-sure switch in feeder circuit to operate. 

35Atmospheric Conversion: Item # 1-00-232200, provides automatic ll, and converts the heating system plumbing from pressurized

08/11IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your appliance please provide model number an

08/11IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your appliance please provide model number an

08/11IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your appliance please provide model number an

08/11IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your appliance please provide model number an

4                           

08/11IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your appliance please provide model number an

41BTU Input Range= 0, and 9350 to 113,900*0 BTU if system is satised.Min. Burn = 1.1 pound per hourMax. Burn = 13.4 pounds per hour* 850

42GREEN/YELLOWDARK BLUE PELLET BOILER WIRING DIAGRAM4" SQUARE JUNCTION BOXBLACKGREEN/YELLOWWHITEREDREDWHITEGREEN3/8"FLEX CONDU

43 “105 Series” PELLET BOILERWHITEGREENRelay enclosure box -GRAINGER # 1EGH7REDREDWHITEGREENDPDT RELAY flange mtd. -GRAINGE

44WoodHearth & Home Technologies, Inc.WARNING: Risk of fire - Do not operate with the flue draft exceeding -.9 in Water Col

45

46

47Proudly Printed On 100% Recycled Paper

1 Turn Mode Selector to OFF.2 Use heat exchanger cleanout rods to clean the heat exchanger tubes.**3 Scrape the air holes in the burnpot.**4 Fill

5HARMAN™ CENTRAL HEATING PRODUCTS LIMITED WARRANTYHearth & Home Technologies Inc., on behalf of its Harman™ brand (”HHT”), extends the fol

6Boiler Kit Materials: (Refer to page 3)List of items contained within the boiler kit shipped with the unit. 1 - Control board cover 1 - Acc

7Design:The rst thing that needs to be done is deciding where and how the boiler will be installed.Things that need to be taken into considera

8NOTE: All installation clearances and restrictions must be adhered to.INSTALLATION IS TO BE PERFORMED BY A QUALIFIED INSTALLER.NOTE

9Requirements for Terminating the VentingWARNING: Venting terminals must not be recessed into a wall or siding.NOTE: Only PL vent pipe wall pass-throu